Some laptops, such as Mac laptops, will require you to unscrew several screws around the border of the case. Be careful of any ribbons or cables attached to the motherboard from the bottom panel. If you find any cables or ribbons attached, make a note of where they are attached, and carefully remove them. This will prevent you from accidentally harming your computer's delicate internals with static electricity.
You can ground yourself by touching something metal or by purchasing static wrist bands that you wear while you work on your computer. Remove the battery if possible. Most laptops will allow you to remove the battery, which will prevent you from inadvertently shocking yourself during the hard drive installation. Open the hard disk panel if present. On some laptops, the hard drive may be housed inside a special panel.
The panel can usually be identified by the hard drive logo printed next to it. You will usually need a small Phillip's head screwdriver in order to remove the screws and the panel. Unscrew the hard drive.
Depending on the laptop, the hard drive may be secured in place with screws. Remove all screws holding the laptop in place. Remove the existing hard drive if necessary. Slide it out from the connection port that it is attached to.
There may be a release latch or ribbon you pull to disconnect the hard drive. The hard drive will pop back about half an inch, allowing you to remove it from its housing.
You may also need to disconnect your hard drive from a wire or cable. It's best to place your old hard drive somewhere safe in case you need to retrieve data off of it. Insert your new hard drive. Ensure that you insert it with the correct side facing out, then press it firmly into the connectors. Do not force the hard drive, or you may damage the connectors.
If you had to remove screws to remove the original hard drive, screw them back in as well. Use a screw to secure the SSD to the motherboard. Connect any wires that you unplugged. If you had to detach any wires or cables from the original hard drive, reattach them to the new hard drive. Close back up your laptop.
Replace the bottom of the case and any screws holding it in place. If you needed to disconnect any ribbons or cables to remove the bottom panel, be sure to reconnect them before closing the laptop. Do hard drives come with the needed cables or will I need to purchase them separately? They don't. You either get the cables with the motherboard or you buy them separately. Not Helpful 1 Helpful Can I take an old hard drive out of one computer and put it in as a backup storage drive in a new computer with a different operating system?
You'll have to reformat your hard drive, but yes, you can use that hard drive as extra storage for almost any PC. Not Helpful 1 Helpful 5. Talking to a tech professional like a specialist at a store selling computers and related items would be best. However, the word 'need' is misleading, as you can use a lot of different hard drives in some laptops.
Not Helpful 6 Helpful 9. I have replaced a hard drive that's fully loaded, but my PC cannot recognize it. I am told to reboot, but either the screen is blank or I am told to replace my battery, which doesn't help either. What should I do. If by "fully loaded," you mean that you have taken out a hard drive from a different computer that had the operating system already installed on it and put it into a new computer, this unfortunately will not work.
The drivers that were installed with the operating system on your older computer are almost certainly not compatible with the drivers needed for your new computer. You will have to back up all of your stored data desktop, documents, downloads, music, photos, videos, etc.
Not Helpful 1 Helpful 4. Try to find screws that will match the necessary size, either in a shop or online. A friend or colleague might also have some spare ones you could use. You can also connect the laptop's hard drive without any screws.
The connection is quite firm, but it's still safer with screws since they ensure that the connection between the drive and laptop doesn't come loose. Not Helpful 0 Helpful 3. Try to fix it. However, if it doesn't load Windows then it's best you take it in to a specialist, most have programs that run from a disk that can check for errors, or they can fix mechanical faults or tell you to buy a new one.
If you still have a receipt, maybe ask for a new one. Not Helpful 9 Helpful 8. You need a Phillips screwdriver to open your computer although most desktops have thumbscrews , and if you are installing an SSD drive, then you might need a 2. Include your email address to get a message when this question is answered. Hard drives emit heat when they are running. If your computer has multiple hard drive bays, consider positioning your hard drives so that there is empty space between them to help keep your computer running cooler.
Helpful 0 Not Helpful 0. Pay close attention to static electricity when working with the inner components of your computer. You can use an anti-static strip or touch the screw on an active light switch cover to ground yourself before touching the components and cables inside your computer. Not all computers will support having their hard drives replaced, especially in the case of laptops.
Helpful 0 Not Helpful 2. You Might Also Like How to. How to. About This Article. Written by:. If you are interested in the content, you can keep going.
What is SATA? It almost supports all computer motherboards and operating systems. SATA drives are usually one of two sizes: 3. The disk of the SATA drive rotates at different speeds according to the model purchased. The speed can reach 10, RPM to increase data transmission. Storage devices used in large servers can even reach 15, RPM.
Mechanical failure is one of the main disadvantages of SATA drives. This makes the movement of the SATA hard drive more flexible. The cable is easier to entangle with the SATA cable since it can move inside the loop to leave more space. The increased speed is very useful for loading images, videos, and larger documents.
If you like playing games, high data transmission speed means you can get a smooth and better gaming experience. The design goal of the SATA standard is to support backward and forward compatibility. This technology was invented to reduce your workload. The ATA interface version does not support hot-swap, which means you cannot change or replace parts while using the computer.
SATA hard drive supports hot-swap. In the long run, the SATA hard drive can extend the lifespan of your computer and improve performance. The hot swapping function can be used to add and delete external devices such as USB without rebooting the entire computer system. SATA is designed to work by transferring data in a single bus, while ATA hard drive uses different wires to transfer data and information.
SATA can be used to connect the hard drive to the motherboard of the computer system, and even connect the hard drive to the hard drive. Although SATA is faster, it is usually more expensive. Hint: You probably want GPT. This is a much more modern, robust and future proof method of partitioning. MBR is the old way of partitioning. You can only format disks up to 2TB in size and create 4 primary partitions. There are ways of adding more partitions but it gets messy.
The only reason you would ever choose MBR these days is if you use an old operating system e. By default, this will be set to the size of the entire disk which is fine for most people. You can optionally slice the disk up into several small partitions, each with their own drive letter in Windows. The next screen asks you to chose a drive letter or NTFS mount point. Choose whatever you like here, Windows will only allow you to choose unassigned letters.
We would advise against choosing the letters A or B however, as these were traditionally used by Floppy drives and may not detect correctly in very old programs. Check the below before proceeding. FAT32 and exFAT can be useful if you need to move the hard drive to a machine that uses a different operating system later.
You can set a custom Allocation unit size to help optimize the performance of the drive and balance wasted space but this is only really needed in extreme example. This is the name of the new drive as it appears in Windows. Give the new drive a descriptive name so you know what it is later. With the low cost of hard drive space we recommend against using file and folder compression in Windows.
The performance hit and other complications are not worth the space savings in our opinion. Choose your desired file system type, allocation unit size, volume label and hit next. Check the disk management screen again. After the disk is finished formatting this should be almost instant if you chose quick format you should see a drive letter associated with your new hard drive.
This is how your new drive will be identified by Windows from now on. Open up Computer or Explorer from the start menu and check out the new drive. Try copying some files onto the drive any ensure everything is operating as expected.
0コメント